Tag Archives: Nissan Consult-3 plus

How to install Nissan Consult 3 plus v65.21 on Windows XP

Posted on by
Reply

This is a how-to guide of a step-by-step instruction on Nissan Consult 3 plus v65.21 installationon Windows XP system.

First, you need a working Nissan Consult 3 plus software:

Crack!!

No pass!

Tested ok!

Safe to use!

Compatible device:

100 works no issue with Nissan Consult iii plus

Operating System Requirements:

Windows XP SP2 Professional Edition operating system or higher

Installation Notes:

  1. Before installing the software, turn off the firewall, antivirus software, 360, etc.
  2. Software should be installed in C drive, and C drive must be “NTFS” format.

How to install Nissan Consult 3 plus v65.21 software:

  1. Run “start.html” by iexplore.exe;
  1. Run “C3PCheckLicense.exe” in folder “C3P License”;
  1. Run “v80003T_20101215_x32.exe” to enable bluetooth;
  1. Run “Pplus_V51.1F.exe” in folder “ReprogramData”.

Now, Nissan Consult 3 plus v65.21 works like a charm.

www.obd2france.com all rights reserved, Original Article url:How to install Nissan Consult 3 plus v65.21 on Windows XP

Nissan Consult 3 Plus V61.10 GTR 41.10 Download: Tested YES

Posted on by
Reply

Free download v61.10 Nissan consult 3 plus software crack:

Free download GTR v41.10 consult iii software:

nissan consult 3 plus software crack features:

Crack

No password

Tested OK

Work no issues on Win XP, Win7, Win8, Win10

21016 Nissan….OK

Nissan car electrolic system diagnosis……OK

ECU programming without a security card……OK

Key programming with the immobiliser security card….OK

Compatible devices: Nissan consult-iii plus (it’s china clone)

How to get Nissan Consult III Plus work with Ford VCM2?

Posted on by
Reply

Have got the alliance vi to work with Consult3 plus software. And make Consult III+ to run it with Ford VCM II interface.
CarDaq
Actica Passthru+ XS
Python1B
Nissan USB Diag
Alliance VI
And The obvious tool VI2
all these are the best to work with Consult 3 plus.
others will also work but maybe not as well.
The Ignition ON its not seen if you use VCM II
I use AVDI and Ignition ON it is not seen too
I read that no matter what j2534 tool you use the Ignition ON its not seen
Probably, only if use Alliance VI2, but alliance vi is quite a bit more complicated to set up
Here is thesetup of VCM II with Nissan Consult 3+.
For ford VCMII
In the Diagnostictool.ini put Ford-VCM-II
Install the consult 3 plus
Install your VCMII Manager and drivers.
In passthru 4.04 in reg edit and rename NISSAN_VI2 To something else
change name Bosch Ford-VCM-II to NISSAN_VI2
Reboot computer and test it
I tested it once with limited success.
Attachment: [Diagnostictool.ini]
https://mega.nz/#!5kMm2TwI!1m7PLJEx_DM_ll3a1UBWuG4ZviRlSyH80iKvJN0-BLk
Note 1: [alliance vi]
The sonde alliance vi is the end for the sonde can clip RTL. remplaced by sonde alliance vi but what is it.
Renault Aliance VCI = 100% Same with Nissan Consult III VCI…
Just & ONLY different name…
Note 2: [workable sw]Clone Consult III (who using patch) for to working with Nissan Consult III S/W, DID NOT working with Clip Software!!!
It seems now Clip S/W needs NEW “Pill” for Clones..

Original:How to get Nissan Consult III Plus work with Ford VCM2?

How to get Consult 3 plus work with NEXIQ usb link

Posted on by
Reply

I’ve been trying to get Consult 3 plus V46.11.00 to work with my NEXIQ usb link. Nexiq supports J2534 so i figured I would give it a shot. I have a CF-19 Tough book which contains all me software for diagnostic. The CF-19 runs in deep freeze all the time to prevent any issues. So I typically test software I acquire on my desktop first. Long story short I installed it on my Desktop edited the .ini file and got it to show connection to my nexiq. (Haven’t tested on a car because my desktop is in my living room). So I thought I was good even wrote a short tutorial to keep with my backups of software. I then installed on the CF-19. Edited the .ini. Expected to the the USB connection with the blue dot…. Nothing. I installed both exactly the same. Im running identical versions Windows 7. There is quite a bit of software on my CF-19 I don’t if its interfering or not. Does anyone have any ideas. To be so close to it working but not able to test is frustrating. Below I will put my short tutorial to show the steps I took and also maybe it will help others. (This is not my work just the steps I found on here)

J2534 PassThru for Nissan Consult 3 plus

1. Install Niassan Consult III+.

2. Make sure the driver for your PassThru is installed.

3. Open regedit.exe

4. Navigate to HKEY_LOCAL_MACHINE > SOFTWARE > Wow6432Node > PassThruSupport.04.04

5. From there choose your device. (For example I have a Nexiq Usb-link, so I choose either ” NEXIQ Technologies – USB-Link” or “NEXIQ Technologies – USB-Link Bluetooth”. I choose to use standard USB-Link)

6. Once you’ve click on your device look in the right column for “Name”

7.Right click on “Name” and choose “Modify…”

8. A window will appear copy exactly what it say in the “Value data:” box. (For example mine is “NEXIQ USB-Link over USB”)

9.Close regedit.

10. Naviagte to “C:\CONSULT-III_plus\System\Application\ApplicationData\CommonSetting”

11. Open “DiagnosticTool.ini”

12. Copy & Paste the text below under “access_mode=1” in DiagnosticTool.ini

with the exeption of putting the text you copied from regedit in place of “!!!!YOUR_DEVICE_NAME!!!!”:

[device]

vi_device_name=!!!!YOUR_DEVICE_NAME!!!!

[mode]

debug_mode=TRUE

debug_mode_vehicle_battery=TRUE”

13. Done

Ps. special thanks to the one share tips above at http://mhhauto.com/

(cracked) Nissan Consult iii v61.10 for ECU programming on Win 7

Posted on by
Reply

Here is the Nissan Consult iii plus v61.10 software, verified ok by obd2express engineers. Come to the first clone version of Nissan Consult iii plus v61.10 to do ECU programming.

Free download Consult iii plus v61.10:

*** Highlights of Consult 3 plus v61.10***

can be used on Windows 7 or XP systems

support ECU Programming (First clone version for it; earlier versions only for diagnosis)

can read security codes and program new keys with specialized security card for Consult 3+

work for all Nissan, Infiniti and Nissan GTR cars to the 2016 year

Feedback on programming with Nissan Consult III plus:

– managed to program TCM and DCM

– sounds great on my an Armada and Titan that have CEL issues which the Consult already paid for itself by helping fix them

– tested successfully it can calculate pin code for key programming, it can also make key but need to get one additional Nissan Consult-3 Plus Security Card, otherwise the button “Immobilizer key” is gray color and is unavailable, Nissan Consult-3 Plus Security Card is expensive to me, so I didn’t order one, but borrow one from my friends and use together with consult3 plus.