Xhorse Condor Dolphin Key Cutting Machine Cut Hyundai Verna Key

Condor Dolphin is the latest portable automatic key cutting machine with a built-in battery inside. And it has all the capabilities of Condor XC Mini. And condor dolphin can bind with VVDI MB Tool to get one token free everyday,we sale Condor Dolphin and VVDI MB Tool bundle package.This blog is about Condor Dolphin Key Cutting Machine Cut Hyundai Verna Key.

1.Xhorse APP,connect condor dolphin with APP via bluetooth.

2.Choose all key lost.Then Hyundai car brand.

3.Check key code and input.

4.M2 clamp,put the new key blade on M2 clamp,fasten it.

5.Click cutting key,continue.

6.Process cutting.

7.Finish.

http://www.xhorsevvdi.com/

How to open a Launch X431 scan tool

The best way to open a Launch X431 scanner:

AND RESULT:

This method works on many scanners like EasyDiag 2.0, golo MDiag, golo EasyDiag +, golo carcare, golo master 2, icarscan, iDiag DBscar……

So if no EOBD, no username and password then you can do this.

PLEASE GIVE REP AND THANKS ONLY IF YOU THINK I DESERVE IT

Using ST-Link:

Install ST-Link, upgrade it STM32 ST-LINK Utility, open ST-Link and select Binary File

1. Target – Connect

2. Target- Erase Chip

3. Target Program and Verify

How to open a Launch X431 scan tool

Clone CarProg Rework for Fast Reprogramming

Finally, I made a modification to my Carprog clone for fast reprogramming, if I need to do it again will not be necessary to open it again and redo all connection every time I want or need to reprogram:

I used the Carprog pins from 15 to 21, those pins are useless for the programmer or any adapter, they are disconnected:

I used a “selector” like the desktop’s pc for bios, to select the programming mode, in picture from left to right: 1, 2 3, if the jumper is placed at pins 1 and 2, the pin 55 (reset) from the AT91 is shorted to ground, preventing deprogramming or programming the MCU, if the jumper is placed at pins 2 and 3 the pin 55 is shorted to vcc 3.3v and the Mcu is placed in ERASE MODE. Without jumper the mcu is placed in programming mode:

Now is probably a waste of time, in the near future will save me some time but from now I can reflash the AT91 in less than 5 minutes.

Update: I forgot to mention that I doesn’t need to remove the AT88SC eeprom to ERASE/REFLASH the AT91 mcu. After that the Carprog works well. This is MY OWN experience, so, If you want to do the same, do it at YOUR OWN risk.

original: Clone CarProg Rework for Fast Reprogramming

How does Xhorse Dolphin cut Suzuki with M1 clamp?

Xhorse Dolphin cut Suzuki with M1 clamp 100% ok, and the whole process is controlled by connecting to your phone by Bluetooth.

Suzuki 2135

Here we go for procedure:

Tap “Setting” to connect Bluetooth.

Tap “All keys lot”.

Choose “Suzuki”.

Input “2153” and tap “Query”.

NI02T (6 Bitting 770 * 2450 M1 Clamp…)

Follow the diagram to fix the key into the M1 clamp.

Choose “Cutting key”.

Continue.

Cutting key.

The cutting process can be seen on the phone and meanwhile on the Condor Dolphin display screen.

Cutting key completed.

Take out the key and insert into the EIS to test if it is working.

Done.

original:How does Xhorse Dolphin cut Suzuki with M1 clamp?